A Manufacturing Company

Solids Control Equipment

• FS300 Shale Shaker
Features an adjustable single deck with 3 panel screens, loop isolators, 58.5 square feet of screen area, and a basket powered by two 2.5HP, 3-phase 230/460V 60Hz explosion proof Vimarc Vibrator motors.

• Single Standard Shale Shaker
SSS orbital motion, single deck shale shaker with hard rubber shock mounts, 20 square feet of screen area for 4’ x 5’ hook strip screens, and powered by a 5HP 3-phase 230/460V 60Hz explosion proof Vimarc Vibrator motor.

• Dual Standard Shale Shaker
DSS orbital motion, single deck shale shaker with hard rubber shock mounts, 40 square feet of screen area for 4’ x 5’ hook strip screens, powered by a 5HP 3-phase 230/460V 60Hz explosion proof Vimarc Vibrator motor.

• Single Tandem Shale Shaker
STS orbital motion single deck shale shaker with hard rubber shock mounts 40 square feet of screen area for 4’ x 5’ hook strip screens, flow back pan beneath upper screen, and powered by a 3HP 3-phase 230/460V 60Hz explosion proof Vimarc Vibrator motor.

• Dual Tandem Shale Shaker
DTS features two orbital motion tandem deck shakers, mounted on a common base with common possum belly deck shale shaker with hard rubber shock mounts, 80 square feet of screen area for 4’ x 5’ hook strip screens, flow back pan beneath upper screen, and powered by a 5HP 3-phase 230/460V 60Hz explosion proof Vimarc Vibrator motor.

• Junior Standard Shale Shaker
SSS orbital motion single deck shale shaker with hard rubber shock mounts, 9 square feet of screen area for 3’ x 3’ hook strip screens, powered by a 3HP 3-phase 230/460V 60Hz explosion proof Vimarc Vibrator motor.

• Mud Cleaner/Conditioner System
Features a FS300 linear-motion shale shaker with a variety of possible desilter/desander cone arrangements manifolded above the screen deck. Space saving model that can flow up to 1000/GPM.

• Desander
Features a manifold constructed of 8” Sch 40 pipe mounted on an angle iron base, 10” cones with grooved end inlets and overflows. Desanding capacity from 500 to 1500/GPM.

• Desilter
Features a manifold constructed of 6” Sch 40 pipe mounted on an angle iron base, 4” or 5” cones with grooved end inlets and overflows. Desilting capacity from 400 to 1280/GPM.

• Mud Agitator
Every O’Drill MCM Mud Agitator features an Ultra-tough Cast Iron gear box (nominal ratio 30:1) and precision-ground gear sets to eliminate backlash. This helical-bevel gear box achieves the highest efficiency available. Our Mud Agitators are available in 3HP to 30HP sizes.

• Mud Hopper
Our Mud Hopper is available in 4” and 6” sizes with butterfly valve, Venturi discharge nozzle, jet nozzle, tees, studs and a sack cutting table capacity up to 650/GPM.

• Low Pressure Mud Gun
Our Mud Guns are available in 2” and 3” sizes with a swivel joint, handle and jet nozzle at the bottom to stir tanks with lengths to meet your tank depth requirements.

• Mud Bucket
O’Drill/MCM Mud Buckets are designed to prevent drilling fluid loss on the rig floor. The O’Drill/MCM Mud Bucket is a cost effective tool, which will reduce wash downs due to a slippery rig floor. The O’Drill/MCM Mud Bucket is 6’ x 11-3/4”. Made to fit drill pipe sizes from 2-3/8” to 5-1/2”. Now available in a 4’ model!